How To Clean A Shark Vacuum Cleaner (6 Easy Steps You Must Read)

In the world of homecare products, very few brands can measure up to Shark’s level when it comes to hygiene and sanitation. This brand’s vacuum cleaner is indeed a spectacle of aesthetics and efficiency, which makes it a popular household name.

From manual models to automatic self-cleaning versions, the Shark vacuum cleaners are actually well ahead of their time. They also have an amazing operating life. So, these products will last you for a really long time as well.

However, the vacuums are only as good as the regularity with which you clean and maintain them. It is imperative that you know how to clean a Shark vacuum cleaner, especially with all the components it has and the accuracy it requires.

Once you go through our informative steps and procedures; it will seem like a breeze.


How to Clean a Shark Vacuum? Maintain Your Shark Vacuum Like A Pro.

Before you get down to cleaning, you’ll need to have some tools and products at hand to execute the procedures. These items include

  • Soap
  • Scissors to cut hair & debris.
  • Microfiber cloth
  • A bucket
  • Vinegar
  • Baking soda
  • Clean water.
  • A screwdriver to open its parts.
  • And protective gloves.

Now that you have your necessary materials, here is a step-by-step method that can help you keep your device working on full steam. Keep on reading to make cleaning your Shark vacuum cleaner easier than ever!

Step 1: Disconnect and Deconstruct

Disconnecting the device from its power source is the obvious first step to cleaning it. Forgetting to unplug may result in electrical accidents, and consequently, cause harm to you.

Once you have disconnected the device, start deconstructing it part by part carefully. Make sure to remember which components fit where, as it will help you save time and efficiently without any hassle.

Step 2: Clear Out Dust Containers

After the disassembly is over, move ahead and start cleaning out the dust canister. Transfer the debris into a disposable plastic bag. Be sure to do this outside, as there is a risk of the dirt falling away from the sides.

Once you have cleaned out the dirt canister, dip it in a water and detergent mixture. Start wiping it with a microfiber cloth. Then go ahead and wash it with cold water. Leave it out to air dry completely.

It usually takes an entire day for the canister to dry thoroughly. Move ahead and reassemble it afterward.

Step 3: Cleanse the Filter

Once you have taken out the dusk container from the machine, you’ll see the filters next. The build material of these parts includes foam rubber and felt, based on the model.

Put the filter into a bucket of warm soapy water, and wash it rigorously. It may look like there are residual stains on filter after soaking. Ignore that and focus solely on cleaning.

If your filter is made of felt, then do not soak it; as it might get damaged easily. Take a damp washcloth. Gently wipe it across the filter to ease the dirt out. Then, wipe it off. Once you’re done washing, be sure to remove the excess soap away from the filter’s body.

Finally, lay it down flat on the body of the component, and dry it for a minimum of 24 hours before reattaching.

Keep in mind, different models of vacuum use different filter types. Some vacuum models use HEPA filters. All the HEPA filters are not washable. So before starting to clean vacuum filters have a close look at its seal or read the manual carefully, is washable or not.

Step 4: Scrub the Brush Head

The rotating brush tends to be the dirtiest part of the device, as dirt tends to get stuck to it the most. So, prepare for cleaning debris, fur, and strands of hair tangled on the brush head.

First, detach the floor attachment from the handle. To do this, most vacuum cleaners have buttons on either end. They will release the brush head when you press them.

Remove the excess dirt tangling from the rotating brush head by cutting it with scissors then pulling it out. Exercise extra caution when doing this step; or else, you may end up damaging the bristles.

Take a toothbrush. Soak it in water, and begin scrubbing the brush head to get the thicker dirt out. Once you’re done cleaning it, let it dry off for a day before putting it back onto the device.

Step 5: Hose Down the Hose

Start by checking for clogs in the hose by dislodging it. If there are any clogs, pour hot water in it, and then shake it.

Then, pour a baking soda and vinegar solution inside the hose. Cover both ends with your hands, and shake it again for a while.

Put it flat on the ground, and allow it to dry for at least a year. Then, carefully reattach it to avoid cracking.

Step 6: Wipe the Floor Nozzle

Before cleaning, inspect the nozzle for possible blockage. Flip it upside down, tap lightly for the debris to loosen, and then remove it using a toothbrush.

Be mindful of the lower duct hose, which is a part of the floor nozzle. Check for blockages and clog openings in it as well. Vigorously clean out the part, and then ensure there is smooth passage for suction.

Then, give the nozzle a good cleaning like the hose, and allow it to dry. Finally, air-dry it and carefully assemble the pieces together. Reattach it to the vacuum with care.


How Often Should You Clean Your Shark Vacuum Cleaner?

I am sure, you secretly dread a question in your mind, how often should you vacuum your place, right?

To be straight forward, It depends on how frequently you use your vacuum cleaner and how you maintain it.

According to the shark’s user manual, the filters should be cleaned at least once every three months. And the HEPA filters can serve you at least two years without any trouble. If you notice any efficiency dwindling of the filters, you may need to clean or replace them from any shark store.

Every vacuum cleaner requires proper maintenance to lasting long. For continuously working well, we suggest cleaning your shark at least once every three months.

Here are some signs which indicates its time to clean your shark vacuum. These includes:

  • Loose or Reduce Suction Power.
  • Unpleasant Odor From Inside The Vacuum.
  • Vacuum Cleaner Produce Loud Noise.
  • Throughout dirt while vacuuming.

FAQ’s on How To Maintain A Shark Vacuum Cleaner.

Can you wash the canister of a shark vacuum?

Yes, You just need to soak it in soapy water and gently wash it using microfiber cloths. Rinse it in cold water and let it to dry completely before reinstall it in back.

Are shark HEPA filters washable?

HEPA filters are normally not washable. You can wipe off the dirt’s gently by tapping with a soft brush. If the filters looks worn out, this is the best time to replace it for working well.


Bottom Line

Cleaning out a vacuum cleaner by Shark is a complex process because of all the components it has. However, the individual steps that we have shown here make it seem like child’s play.

Hopefully, you’ll never have to worry about maintaining your Shark vacuum cleaner ever again. Just be sure to reassemble the parts carefully after cleaning, as one wrong move can lead to horrible device malfunctions.

Now that you know how to clean a Shark vacuum cleaner, your vacuum will operate smoother than ever for as long as possible.

Do you have any questions in your mind? Just leave a comment below we will get back to you soon.

Spread the love

Founder of HomeGear Guider, a business entrepreneur, market researcher and independent writer. My aim is to help people by figuring out the best products in market. I have worked more that 10 years as a product analyst and market researcher for consumer product companies in USA and UK. You can reach Jon Grant at-

We will be happy to hear your thoughts

  1. Good day! This post could not be written any better!

    Reading through this post reminds me of my previous room mate!
    He always kept talking about this. I will forward this write-up to
    him. Pretty sure he will have a good read. Thanks for sharing!

    Reply

Leave a Comment